Our service team is professionally trained and certified to handle a multitude of situations from routine maintenance to repowers and extensive restoration projects. We work with all motors from two-stroke outboards through diesels as well as gensets. Out team is equipped to handle a medley of other services including electronics installs, rewiring, preventative maintenance & more!

Spring Reactivation:

In the spring we will send one of our techs to you ensuring your vessel is in proper working condition. We will go through all the systems and perform a 25pt inspection to help you start your season off on the right foot. We go through all the systems on your boat and highlight any potential problems and snag them before they become a headache.

Heres a sample spring reactivation plan:

  1. Cleaning battery terminals & load test battery
  2. Check & top off all fluids including oil, anti-freeze & power steering fluids
  3. Grease steering cables & add fluids to hydraulic systems
  4. Test trim pump & lines and top off fluids
  5. Check throttle & shift cables
  6. Inspect belts & block drains for cracks
  7. Inspect lower unit gear lube, transmission fluid & crank case fluid to ensure they are at the proper levels
  8. Ensure fresh water & raw water pumps are functioning properly
  9. Test navigation lights, horn & ensure USCG safety standards are met & current
  10. Sea trial to verify proper RPM's and speeds are reached

Basic Service:

  • Oil Changes
  • Change Spark Plugs
  • Check & replace filters as needed
  • Inspect risers & manifolds and change if needed
  • Remove & inspect outdrives for any damage, check bellows and gimbals and repair as needed

Electronics install/refit & vessel rewiring:

If you're looking to give your dated electronics a facelift, our team is qualified to handle the job. We can remove and install new electronics and rewire your boat. A sample of some of our electronic services include:

  • GPS chartplotters - Radar - Autopilot - Fishfinders/depthsounders - VHF radios
  • AIS systems - Marine Weather - Thermal Cameras - Sound Systems - Speakers
  • Amplifiers - Satellite radio - Bluetooth - I-pod dock & integration - Satellite TV
  • Flatscreen TV’s - Security systems - Monitoring systems - Bridge cameras
  • Cockpit cameras - Platform cameras - AC/DC systems - Outlets - Exterior lights
  • nterior lights - Spotlights - Underwater lights

Ala Carte:

  • Shrinkwrapping
  • General Handiwork
  • Warranty Work

Winterization:

Outboard Winterization & Preventative Maintenance

  • Add fuel stabilizer
  • run the engine to temperature, flush with fresh water, fog engine with rust preventive oil mixture
  • drain gearcase, inspect for impurities and refill
  • change crankcase oil and filter
  • change the remote fuel/water separator filter
  • remove and inspect the propeller, lubricate the shaft, and re-install 
  • lubricate all engine grease fittings, and inspect and replace zincs as needed (propeller reconditioning is additional if needed)
  •  Disconnect battery cables, clean and lubricate terminals
  • reset all maintenance parameters
  • all services included in standard winterization
  • run the boat and check engine for proper function
  • remove the lower unit and install new water pump impeller and gaskets and inspection of wear plates and housing
  • replace all engine fuel filters (other than V.S.T. filter)
  • pressure check your gear case
  • check operation of the power trim pump
  • spray the entire engine with rust inhibitor
  • touch-up the paint on the lower gear case as needed

Outboard Tuneup

  • check cylinder compression
  • install new spark plugs
  • replace all engine fuel filters (other than V.S.T. filter)
  • check and adjust timing at idle
  • check and adjust throttle and shift linkages
  • check for proper adjustment of the engine oil injection system
  • check engine electrical wiring
  • lubricate all linkages
  • run a computer diagnostic analysis to check all manufacturers' specifications on 4 stroke, Optimax, & H.P.D.I. engines
  • reset all maintenance parameters

Inboard/Outboard Winterization & Preventative Maintenance

  •  We check all systems including oil pressure, charging system, and water temperature including flushing scale from engine petcocks
  • We change your oil, oil filter, and fuel/water separator filter
  • We check fluid levels on power steering, power trim, and trim tabs pumps 
  • We inspect all engine hoses and fuel lines, lubricate all linkages, inspect and replace engine zincs as needed, inspect all drive belts, and touch up paint
  • We add fuel stabilizer, run the engine and flush with fresh water
  • We drain, run antifreeze thru, and fog the engine with a rust preventative oil mixture and coat the engine with rust inhibitor to prevent corrosion
  • Disconnect battery cables, clean and lubricate terminals

I/O Tuneup

  • check the cylinder compression
  • nstall new distributor cap, rotor/sensor assembly, spark plugs, P.C.V. valve, and all engine fuel filters
  • We clean the flame arrestor; check the timing, the idle speed and the control adjustments
  • We perform computer diagnostic analysis to check all manufacturers' specifications

Outdrive Winterization & Preventative Maintenance

  • remove the outdrive, lubricate the gimbal housing, universal, and tail shaft
  • drain the gear case, inspect the fluid for impurities and refill the gear case
  • remove and inspect the propeller, lubricate the shaft and re-install propeller
  • lubricate steering, pivot, and shift cables, re-torque gimbal ring to steering shaft connection
  • inspect all bellows and hoses
  • pressure test the outdrive
  • clean the shift cavity and all internal water passages
  • check the gimbal bearing and alignment and touch up the paint
  • inspect and replace all outdrive zincs as needed
  • replace the outdrive gasket and o-ring kit, and re-install

Inboard Winterization & Preventative Maintenance

  • We check all engine systems including oil pressure, charging system, and water temperature including flushing scale from engine petcocks
  • We change your oil, oil filter, and fuel/water separator filter
  • We check fluid levels on power steering, power trim, and trim tab pumps, inspect all engine hoses and fuel lines, lubricate all linkages, inspect and replace engine zincs as necessary, inspect all drive belts, and touch up the paint
  • We add fuel stabilizer, run the engine and flush with fresh water
  • We drain, run anti-freeze through, & fog the engine with rust preventive oil mixture, & coat engine with rust inhibitor to prevent corrosion
  • Disconnect Battery cables, clean and lubricate terminals

Inboard Tuneup

  • We check cylinder compression, install new distributor cap, rotor/sensor assembly, spark plugs, PCV valve, and all engine fuel filters
  • We clean flame arrestor, check timing, idle speed, and the control adjustments
  • Perform computer diagnostic analysis to check all manufacturers' specifications

Diesel Winterization & Prevantative Maintenance

  • We change the engine oil and oil filter, and inspect for any leaks
  • We change all the fuel filters, filter elements, and coolant filters
  • We check coolant with refract meter
  • We inspect all belts, hoses, and fuel lines
  • We replace any air filters as needed
  • We add fuel stabilizer and flush the engine with antifreeze
  • We spray the entire engine with rust inhibitor to prevent corrosion and seal out water during storage
  • We inspect and replace engine zincs as needed
  • We drain the oil, inspect for impurities, refill, change the filter, and just and lubricate the linkages
  • visually inspect the propeller shaft, strut, and cutlass bearing

IPS Winterization

We drain the oil, inspect for impurities, refill, change the filter, check power steering fluid, change zinc, remove and visually inspect the propellers and shafts, lubricate and reinstall